Fridge not cooling — freezer fine, fresh-food side warm.
Evaporator iced over behind a failed defrost heater and thermostat.
Replaced the defrost heater and thermostat, cleared the ice — steady temps the same day.
Same-day, in-home Whirlpool appliance repair across Calgary, Chestermere, and Okotoks. We fix the faults Whirlpool owners call about most — washers that won't drain or throw an F-code, dryers running with no heat, ice makers that quit, and dishwashers that won't start — plus fridges, ovens, and ranges.
Local technicians who know the Whirlpool platforms inside out — the direct-drive and Cabrio washers, the Duet laundry pairs, and the F-series fault codes — and bring the right parts to your door.
Book online or call — a local technician locks in a same-day window and arrives with common Whirlpool parts on the van, ready to diagnose and repair in a single visit.
We diagnose and repair the Whirlpool faults homeowners across Calgary, Chestermere & Okotoks actually call about — explained plainly, quoted upfront.
A flashing “PO” only means a power outage was detected — it clears from the display. A fridge that's actually warm is usually the adaptive defrost control, defrost heater or evaporator fan, which we test directly.
Diagnose the cooling system, defrost control and ice maker, quote upfront — most fixed same-day.
F9 E1 is a drain fault — water didn't pump out in time; F6 E1 means no water was detected at fill. We test the pump, inlet valve and float before replacing parts.
Clear the drain path, test the drain pump, water-inlet valve and float, and restore proper draining and cleaning.
An “AF” code flags restricted airflow — usually a clogged vent. A dryer with no heat is more often the heating element, thermal fuse or thermal cutoff (gas: the igniter), which we test as a full circuit.
Test the heating element, thermal fuse, thermostats and gas igniter, clear the venting, and restore full heat.
F21 is the classic Duet “long drain” — usually a clogged pump or filter, not a new board; Sud means it's fighting too many suds, and dL is the door lock. We trace the real cause before swapping parts.
Diagnose the drain pump and filter, door lock, and spin/balance faults — and the F-codes behind them.
A Whirlpool oven that won't heat usually comes down to the bake element or the temperature sensor (often an F3 or F4 code); an F1 points to a control-board fault — we test each before quoting.
Test the bake and broil elements, oven sensor and control board, and restore even, accurate heat — gas and electric.
We service Whirlpool gas, coil, smooth-top and induction surfaces — from a single dead plug-in element to an igniter that sparks but won't light.
Repair burners, elements, igniters and induction coils — and the surface controls behind them.
Whether it's a Whirlpool washer that won't drain (the F21 code), a dryer running with no heat, or a fridge that's stopped cooling, a local technician brings the know-how and the right parts to your door — same-day across Calgary, Chestermere, Okotoks, and the surrounding acreages. Find your area below.
A sample of the Whirlpool faults we see most across Calgary, Chestermere and Okotoks — the problem, what we found, and how we fixed it.
Fridge not cooling — freezer fine, fresh-food side warm.
Evaporator iced over behind a failed defrost heater and thermostat.
Replaced the defrost heater and thermostat, cleared the ice — steady temps the same day.
Standing water in the tub and an F9 E1 drain code.
Drain pump jammed with debris, so it couldn't pump out in time (F9 E1).
Cleared the pump and check valve, tested the drain — draining clean in one visit.
Dryer running but no heat — loads coming out damp.
Open heating element, with a thermal cutoff tripped by a clogged vent.
Replaced the element and thermal cutoff, cleared the venting — full heat back in one visit.
Front-loader stuck on F21, water left in the drum after the cycle.
F21 long-drain from a clogged pump filter — a sock and coins caught in the trap.
Cleared the pump and filter trap, tested a full cycle — drains and spins clean.
Ice maker quit, then froze into a solid block.
Failed ice-maker module plus a slow water-inlet valve leaving water to refreeze.
Replaced the module and inlet valve — making clean ice again.
Gas oven wouldn't reach temperature — burners working fine.
Weak bake igniter not drawing enough current to open the safety valve.
Replaced the bake igniter — oven holding temperature again.
Tell us which Whirlpool appliance is acting up — washer, dryer, fridge, dishwasher or range. We'll confirm a same-day window and bring the upfront quote to your door — no obligation.
Your message has been sent successfully. We'll get back to you shortly.
Upfront quote · No obligation · 90-day warranty
We'll be in touch shortly to confirm your same-day Whirlpool repair window and bring an upfront quote to the door.